In today's post I share with you a complete step by step photo tutorial guide on how to paint a Necron Warrior from the Indomitus set in a paint scheme I devised for my Occiputek Dynasty. More after the jump!

This tutorial assumes you have a basic understanding of how to paint. For the beginners, I will explain the techniques as I go along. Each picture below shows four chronological steps. Underneath each picture are the corresponding instructions. Each step shows the paint I used during that step.

Paints you will need for this tutorial:
Black Undercoat
Castellax Bronze (Layer)
Leadbelcher (Base)
Contrast Medium (Technical)
Nuln Oil (Shade)
Agrax Earthshade (Shade)
Brass Scorpion (Layer)
Stormhost (Layer)
Mechanicus Standard Grey (Base)
Celestra Grey (Base)
Kantor Blue (Base)
Teclis Blue (Layer)
Lothern Blue (Layer)
Corax White (Base)
Wraithbone (Base)
Skeleton Horde (Contrast)
Screaming Skull (Layer)
Snakebite Leather (Contrast)
Temple Guard Blue (Layer)
Ulthuan Grey (Layer)


1. Undercoat the model black. 
2. Paint the Necron torso and limbs with Castellax Bronze. ToP TIP: A touch of Lahmian Medium in your metallics will make them smoother to paint with.
3. Paint the torso and limb armour sections with Leadbelcher leaving the skeletal pistons and joints as Castellax Bronze.
4. Mix 3 parts Nuln Oil with 1 part Contrast Medium and wash over the entire model. The Contrast medium helps pull the wash into all the recesses intensifying the shading.


5. Mix 3 parts Agrax Earthshade with 1 part Contrast Medium and wash over the entire model. The Contrast medium helps pull the wash into all the recesses intensifying the shading.
6. Highlight the torso and limb armour by reapplying Leadbelcher. Just do this on the upper parts of the armour where it would naturally catch the light so you leave some of the two previous steps showing through. If you're painting a lot of Necrons you can lightly drybrush this stage. 
7. Highlight the skeletal pistons and joints with Brass Scorpion
8. Fine line edge highlight the metal and bronze areas with Stormhost Silver.


9. Paint some thick highlights of Mecharius Standard Grey on the black weapon
10. Apply thin edge highlights of Celestra Grey over the previous step. .
11. Mix 3 parts Nuln  Oil with 1 part  Contrast Medium and wash the entire weapon to help the blend the layering in.
12. Paint barrels of the weapon with Kantor Blue.


13. Paint the energy cell of the weapon with Teclis Blue. Then paint a thick edge highlight with Teclis blue on all the edges of the barrels.
14. Paint a thin edge highlight with Lothern Blue on all the edges of the barrels.
15. Water down Corax White and paint the head and chest emblem. This might take up to 3 coats.
16. Paint the head and chest emblem with Wraithbone.


17. Thin Skeleton Horde contrast with by mixing 1 part Skeleton Horde with 1 part Lahmian Medium and lightly wash the head and chest emblem.
18. Highlight the head and chest emblem with Screaming Skull. I found highlighting several with thinned translucent layers gave a softer look. You can thin with water or Lahmian Medium.
19. Paint Snakebite Contrast into the deepest recesses like the mouth and nose. .
20. Edge highlight the head and chest emblem with Wraithbone.


21. Mix 1 part Temple Guard Blue with 2 parts Lahmian medium to create a glaze and paint a thin translucent layer around the icon on the chest, between the ribs, the eyes and power core. 
22. Paint the eyes, chest icon, between the ribs and power cell with Ulthuan Grey. 

To finish the bases, PVA glue sand to the base. Once dry, paint the entire base with Steel Legion Drab, then wash the sand with Agrax Earthshade. Once dry, drybrush the sand with Karak Stone. Add static grass and grass tufts to decorate. 

Thanks for checking out my tutorial.


Do you like our tutorials and reviews? Here is what you can do to support us: Check out the websites of our sponsors, place your next orders at Wayland Games by clicking here or at Element Games by clicking hereThank you very much, we appreciate any help to keep us going.